Art.-No. 97299

fischer Highbond anchor FHB II-A L M 8 x 60/30 A4

Top Features

Maximum load values due to large anchorage depth. This means fewer fixing points and smaller anchor plates are required.
Optimised for low axial and edge distances in cracked concrete.
No drill hole cleaning is required when using a mortar cartridge. This saves time.
ETA approval for cracked concrete.
Made of stainless steel for fixings used outside.

The best performance in cracked concrete for maximum tension loads - even outdoors.

Advantages

The large anchorage depth of the anchor rod FHB II-A L allows the system to achieve maximum load values. Thus fewer fixing points and smaller anchor plates are required.
The cone shape of the FHB II-A L anchor rods has been specially optimised for high tensile loads. As a result, the best performance in cracked concrete is achieved.
The FHB II-A L anchor rod is approved for use both with capsules and with injection mortar. This guarantees maximum flexibility in the application.
No drill hole cleaning is required, if the FHB II-A L anchor rod is used in combination with the FHB II-P/-PF capsule. This saves precious installation time.
When using the FHB II-A L in combination with the injection mortar FIS HB, push-through installation with annular gap filling is possible without the use of any further tools.

The fischer Highbond rod anchor FHB II-A L is produced from stainless steel. The torque-controlled composite anchor can be processed with the Highbond special mortar FIS HB or the mortar cartridges FHB II-P and FHB II-PF HIGH SPEED. When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. Using the fischer Highbond system FHB II means that, for example, façades, silos, and heavy steel constructions are securely installed within external areas.

Functioning

The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation.
When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB.
The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole.
When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall.
The styrene-free vinyl ester mortar fully seals the drill hole.
When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art.-No. 62420.

Mounting Strip 1 Picture

1 / 9

Mounting Strip 2 Picture

1 / 5

ETA Certification Document

pdf, ETA-05/0164

European Technical Assessment for fischer Highbond-Anchor FHB II - Torque controlled bonded anchor for use in concrete

Created on 12/14/2017

DOP - Declaration of Performance

pdf, DoP No. 0282

Declaration of Performance for fischer Highbond-Anchor FHB II (Bonded fastener for use in concrete)

Created on 01/19/2021

Test report (fire protection)

pdf, (2103/12/12) - CM

lnjection systems FHB / FHB dyn / FDA

Valid from 07/15/2021
to 07/15/2026

Test report (fire protection)

pdf, GS 3.2/16-352-1

fischer Highbond anchors FHB II and FHB 11 lnject

Valid from 02/07/2017
to 02/06/2027

Filling Quantities

pdf,

Filling quantities für highbond-Anchor FHB II-A L

Installation Instructions

pdf,

fischer FHB II

Load Table

pdf,

Highbond-Anchor FHB II - Permissible loads of a single anchor in normal concrete of strength class C20/25.

Accessories

ETA-approval
Drill diameter ( d₀ )	10 mm
Drill hole depth ( h₀ )	75 mm
Anchorage depth ( h_ef )	60 mm
Thread ( M )	M8
Width across nut	13 mm
UK TRANSLATION MISSING	3
Packaging	Folding box
Amount	10 St.
GTIN (EAN-Code)	4006209972991

fischer Highbond anchor FHB II-A L M 8 x 60/30 A4

The advantages / Product description

Application and approval

Assembly instruction

Technical data

Documents for download